RE- MAKE THE JOINT AND SAND IT
Today I made uo my mind that at any cost, I have to finish making the joint today. Just when I was about to cut the long stick part of this joint, my friend came and showed me a long stick that she found. It was already the shape and the size that I needed. I was so thankful and grateful of her because she made my work much easier. So I took that stick and cut it into the appropriate size because it was much wider and longer that I needed. So I trimmed it into the required size and began sanding it. I was not able to immediately sand it because the sander was being used by another student at that moment, So I had to wait until he finished. That person took a very long time which was annoying me. Even when he clearly knew that I needed to finish this during the lesson and that I was waiting, he was taking his sweet time, talking to friends and even letting some people use the sander. This annoyed me a lot because it was unfair for him to let his friends use the machine when clearly, I was after him. When he began doing such things, I did not hesitate to raise my voice against him. I told him that he ha no right to do that and that I had been waiting since half an hour. That is when he began speeding up. When it was around 20 minutes to the next class, he gave me the sander. I knew that I will not be able to finish making the whole joint during this lesson because I had only 20 minutes left and I needed to make the smaller part of the joint too. But I proved myself wrong and I was very proud about it because I finished making the joint during this lesson itself. I finished sanding the long stick in around 5 minutes because I was very focused and did not get distracted at all. I had challenged myself to finish this task during this lesson and I had to do it at any cost. I liked the way I sanded the long stick because it has a rounded and a blunt edges making it look for cylindrical. It felt very smooth and fine however it was not very even. I could not make it very even because of lack of time. Then I went on and cut the smaller part of the joint. I could not have managed to sand it but I made it smooth using the scroll saw. Then I drilled the hole into the two parts of the and I was one step away from finishing today's challenge. Now all I had to do was take out the nail that I had put in my pencil case from last time, and insert it into this hole! When I did it, I felt a sense of relief flush through me! I felt even better when I moved the joint and folded it and it was still intact. I was very proud of myself for not giving up even when I had failed 3 times! I am very happy that I am done.
Today I made uo my mind that at any cost, I have to finish making the joint today. Just when I was about to cut the long stick part of this joint, my friend came and showed me a long stick that she found. It was already the shape and the size that I needed. I was so thankful and grateful of her because she made my work much easier. So I took that stick and cut it into the appropriate size because it was much wider and longer that I needed. So I trimmed it into the required size and began sanding it. I was not able to immediately sand it because the sander was being used by another student at that moment, So I had to wait until he finished. That person took a very long time which was annoying me. Even when he clearly knew that I needed to finish this during the lesson and that I was waiting, he was taking his sweet time, talking to friends and even letting some people use the sander. This annoyed me a lot because it was unfair for him to let his friends use the machine when clearly, I was after him. When he began doing such things, I did not hesitate to raise my voice against him. I told him that he ha no right to do that and that I had been waiting since half an hour. That is when he began speeding up. When it was around 20 minutes to the next class, he gave me the sander. I knew that I will not be able to finish making the whole joint during this lesson because I had only 20 minutes left and I needed to make the smaller part of the joint too. But I proved myself wrong and I was very proud about it because I finished making the joint during this lesson itself. I finished sanding the long stick in around 5 minutes because I was very focused and did not get distracted at all. I had challenged myself to finish this task during this lesson and I had to do it at any cost. I liked the way I sanded the long stick because it has a rounded and a blunt edges making it look for cylindrical. It felt very smooth and fine however it was not very even. I could not make it very even because of lack of time. Then I went on and cut the smaller part of the joint. I could not have managed to sand it but I made it smooth using the scroll saw. Then I drilled the hole into the two parts of the and I was one step away from finishing today's challenge. Now all I had to do was take out the nail that I had put in my pencil case from last time, and insert it into this hole! When I did it, I felt a sense of relief flush through me! I felt even better when I moved the joint and folded it and it was still intact. I was very proud of myself for not giving up even when I had failed 3 times! I am very happy that I am done.
No comments:
Post a Comment